Skip to content

system.md

Latest commit

 

History

History
98 lines (80 loc) · 5.7 KB

system.md

File metadata and controls

98 lines (80 loc) · 5.7 KB
Raw

sys.b — System Settings, RSTP Bridge, Health

The largest endpoint. One record backing the System page, the bridge half of the RSTP page and the Health page. Polled every 1 s while any of those pages is open.

Boot / identification keys

Returned on every read; the UI reads them once at load time:

Meaning SwOS id Lite id Type Access
Board name (e.g. CSS326) brd i07 str RO
Firmware version (e.g. 2.18) ver i06 str RO
Build timestamp (unix) bld i0b uint RO
Hardware revision rev – str RO (present on some boards)
Marketing name mrkt i2b str RO (SwOS: some boards; Lite: css606/css610/css610out only)
PoE hardware indicator npoe – uint RO (SwOS; also selects fan/temp-sensor count on css354)

System page

Label SwOS id Lite id Type Access Availability / notes
Address Acquisition iptp i0a enum: DHCP with fallback, static, DHCP only RW all
Static IP Address ip i09 ip RW all. css106 id: sip
Identity id i05 str RW all
Allow From (network) alla i19 ip RW composite alla/allm = allowed management network
Allow From (prefix) allm i1a uint ≤ 32 RW
ETH/BOOT Port Enabled mgmt – bool RW SwOS builds with a dedicated management port: CRS312 (runtime), css326q, css326xg, css354
Allow From Ports allp i12 bool (port mask) RW all
Allow From VLAN avln i1b uint ≤ 4095 RW all
Independent VLAN Lookup ivl – bool RW SwOS & css106 only
IGMP Snooping igmp i17 bool RW not Lite ftc21/gpen21/gper14i
IGMP Querier igmq i29 bool RW ditto; UI clears it when snooping is off
IGMP Fast Leave igfl i27 bool (port mask) RW ditto
IGMP Version igve i28 enum: v2, v3 RW ditto
Mikrotik Discovery Protocol pdsc i08 bool (port mask) RW all
Port1 PoE In Long Cable lcbl – bool RW css106 (RB260GSP) only
Dark Mode – i21 bool RW gpen21 only (UI theme)
Power I/O – i20 enum: in, out RO gper14i only
Alarm – i23 enum: inactive, active RO css610out only
Serial Number sid i04 str RO all
MAC Address mac i03 mac RO all
Uptime upt i01 uptime — SwOS: centiseconds, Lite: seconds RO all
Trusted Ports (DHCP & PPPoE snooping) dtrp i13 bool (port mask) RW not css106, not Lite ftc21/gpen21/gper14i
Add Information Option ainf i14 bool RW ditto (DHCP option 82)

PoE Out (single-output devices)

On devices with one PoE output the mode/status live here instead of a PoE page:

Label SwOS id Lite id Type Access Availability
PoE Out Mode poe i1c enum: auto on, force on, off RW Lite css610, gpen21 (present but compiled out in all SwOS 2.18 builds)
PoE Out Status poes i1d enum: waiting for load, powered on, overload, no load, powered on, overload, no load, has load, invalid load, then 3 × psu failed (2.21; ≤ 2.20: bat. low) RO ditto

RSTP bridge settings

Shown on the RSTP page together with rstp.b.

Label SwOS id Lite id Type Access Notes
Bridge Priority (hex) prio i0e uint, UI radix 16, 4 digits RW
Port Cost Mode cost i0f enum: short, long RW
Forward Reserved Multicast frmc i2a bool RW disables per-port RSTP editing while set
Root Bridge rpr + rmac i10 + i11 composite: uint (hex) + "." + mac RO current root bridge priority.MAC

Health page

All read-only except Fan Target Temp. Availability: see the per-build feature tables in models.md.

Label SwOS id Lite id Type Availability
CPU Temperature temp i22 int (32-bit), °C all builds with Health
Board Temperature 1 / 2 btm1, btm2 – int, °C SwOS, count per build (fc flag)
PHY Temperature phyt – int, °C css310g, css312, css326xg
FAN1–FAN4 fan1…fan4 – uint, RPM SwOS, count per build/board
PSU1 / PSU2 (current @ voltage) p1c+p1v, p2c+p2v i16+i15, i1f+i1e composite: uint mA @ uint 0.01 V SwOS css318p, css328p, css354 (non-PoE); Lite css610pi (css610out: voltage i15 only)
PSU1 / PSU2 status p1s, p2s – enum: failed, ok CSS317 & CRS328-4C-20S-4S+ (runtime), css312, css320p, css326xg, css354
PSU1 / PSU2 voltage p1v, p2v – uint, mV (css310, css326q) or 0.01 V (css320p) per build
PSU1 / PSU2 fan p1f, p2f – uint, RPM css320p
PSU1 / PSU2 power p1p, p2p – uint, 0.1 W css320p
PSU1 / PSU2 temperature p1t, p2t – int, 0.1 °C css320p
Power Consumption – i26 uint, 0.1 W Lite css610pi, css610out
Fan Target Temp (C) ftt – int (32-bit), −273…65, RW css310, css310g
Voltage volt – uint, 0.1 V css106 (RB260GSP)
Temperature temp – int, °C css106 (RB260GSP)

css610out additionally has the battery/charger endpoint ups.b on its Health page.

Relationships

  • iptp = DHCP only disables the Static IP Address field; on fallback mode the static address is used when DHCP fails.
  • alla/allm, allp and avln combine into the management-access filter (network, ports and VLAN).
  • The IGMP settings here control the snooping whose result appears in !igmp.b.